Enviro EA800 Manual de Instalação descarregar pdf (Página 2)

2. Unlocking/Locking Base Console

Press F1 to unlock base console. The default password

is 0800.

See Installation/Owner’s Manual to customize password.

To enter password, press F3 (Next) to move the cursor

one digit to the right.

Use the arrow keys to change the numeric value to 0800,

then press  to enter.

The base console is now unlocked.

After completion of steps 3 - 5, press F1 to lock the base

console, if desired.

The base console locks automatically if no keys are

pressed within 30 minutes.

3. Setting Date and Time

To set time and date format: The defaults are

24-hour clock (military time) and mm/dd/yyyy format.

To change to 12-hour clock or dd/mm/yyyy format if

desired, go to MAIN MENU, select System,  ; select

Conﬁguration,  ; select Date Format or Time

Format,  ; then select the preferred conﬁguration.

Press F3 (OK) to set.

To set time and date: go to MAIN MENU, select

System,  ; select Set Date or Set Time,  ;

follow menu prompts and use PREV and NEXT soft keys

to select the desired values. Press F3 (OK) to set.

4. Adding Sensors

Press MENU key, use arrow keys to select Sensors and press  .

Select Add New Sensor,  .

Follow procedure 4a if adding a hardwired sensor and procedure 4b if adding a wireless sensor.

4.a Adding Wired Sensors

Select Wired,  . Select the type of sensor being

connected. You can opt to select from a list of Common

names or create a Custom name (16 characters or less).

After assigning a name, continue to follow the on-screen

prompts to complete the programming of your sensor.

See Installation/Owner’s Manual for details. Repeat setup

for each additional hardwired sensor. The steps vary

depending on the sensor type being added. Note: For

detailed information on conﬁguring a 4-20mA sensor,

please refer to the Installation/Owner’s Manual.

4.b Adding Wireless Sensors

Remove cover from wireless sensors until setup is complete. With the wireless sensor unmounted

and located near the base console, apply power to the sensor using remote power supply or 2 AA

batteries before starting setup. It is recommended that power is applied to one sensor at a time,

and that the setup is completed for that sensor before adding subsequent wireless sensors.

Select Wireless, press  . The base console searches for a connection with the wireless sensor.

This may take 1-2 minutes.

Note: Press the Reset Button on the sensor to restart the search

process if necessary. Verify

that the number shown

on the base console screen

matches the number on the

sensor’s PC board. Press  .

If the list of number(s) on

the screen does not contain the number found on the sensor’s PC board, press F1 (Cancel) to

continue the search process. Select the output relay to which the wireless sensor is to be assigned,

then press  . Continue the setup based upon the type of wireless sensor being added.

Wireless Multi-Function Sensor (EA-WMFS)

Wireless multi-function sensors provide a wireless transmitter for connection to a wired sensor.

Select the type of sensor to be connected to the wireless multi-function sensor, then press  .

Assign a Common name or Custom name to the sensor, and continue to follow on-screen

prompts to complete the setup.

Note: Custom names are limited to 16 characters for all sensors.

Note: The Wireless Multi-Function Sensor (EA-WMFS) supports the following sensor types:

Blue Temperature Probe (TEMP-L-W and TEMP-L-S)

Red Temperature Probe (TEMP-H-W and TEMP-H-S)

White Temperature Probe (TEMP-UL-S)

Supervised WaterBug® Sensor (W-S-S and W-UC-S)

Contact Sensors (N.O. and N.C.)

Note: Not for use with the HA-III+ or 4-20mA sensors. These sensors can only be conﬁgured as

wired.

Wireless Temperature Sensor (EA-WTS)

Assign a Common name or Custom name to the sensor, and continue to follow on-screen

prompts to complete the setup.

Note: Custom names are limited to 16 characters for all sensors.

Wireless Humidity Sensor (EA-WHS)

Assign a Common name or Custom name to the sensor, and continue to follow on-screen

prompts to complete the setup.

Note: Custom names are limited to 16 characters for all sensors.

Repeat setup for each additional wireless sensor. The steps will vary depending on the type of

sensor being added.

Verifying Signal Strength

After temporarily mounting the wireless sensors in the

desired location, verify the signal strength at the base

console by pressing MENU , select Sensors,  ;

select Performance,  ; then select the sensor to

be checked,  . It may take as long as 30 seconds to

acquire the current signal strength.

If No Data is displayed in place of bars, it indicates that

recent signal strength information has not been received.

If this persists for 1-2 minutes without displaying any

performance bars, it is a strong indication that your

sensor is placed out of range with the base console.

If fewer than two bars are shown, it is recommended that

the sensor be relocated to obtain a better signal. Refer to

the instruction sheet included with the wireless sensor for

details on ensuring optimum signal strength.

5. Advanced Settings

Refer to the Installation/Owner’s Manual found online at www.winland.com for conﬁguring the

following advanced EA800 settings:

• Conﬁguring the Relays

• Pausing Monitoring and Cancelling Pause

• Replacing a Sensor

• Editing Sensor Parameters

• Changing Sensor Data Collection Frequency

• Changing the Buzzer Setting

• Clearing the Alarm/Sensor Logs

• Saving/Loading Conﬁguration Settings

• Exporting the Stored Logs

Sensor Model Number

Example: EA-WTS = Wireless Temperature Sensor

Reset Button

1 2

Comentários a estes Manuais

Sem comentários

Enviro EA800 Manual de Instalação Página 2

Comentários a estes Manuais